In installing marble tile Los Gatos, you should be worrying about how complicated this might be. Basically, this could be simple. Thus, here are steps to guide you.
The first matter that that you should be concerned of is to ensure if the flooring is stable by doing a test and in doing so, have it be bare to know its sturdiness. Identifying how sturdy it is is through checking of it will shift or if there are presence of cracks. Also, the bouncing test can be done by requesting another to jump at one place and inspecting the vibration in another spot.
The next matter that need your consideration is how you will level the floor and numerous manufacturer nowadays would certainly give the recommendation that you should follow the standard measure of the slope. You will be obtaining a lot of figures but the highest will be the base. The gaps of the levels should also be taken care of and to solve this, you can use a leveling compound.
Another matter that should not be forgotten is the undercutting of the jambs and to start with this step you have to obtain first a plywood. This will used in determining the thickness of the slabs as well as how thin should the mortar be applied. Then, if you have already determined these, you will now have an idea how the door jambs will be accommodated.
One more matter you should also be taking note of in doing the project is the point of the center which should be marked as that will be necessary for the steps that will be following. You will be able to determine this by by securing the meters of the width and the length of the room. Then, you will have an idea on the whole area to be covered.
Moreover, temporary laying out would be helpful like conducting dry runs since this will be your basis as you plan the set up of the installation. You should start with placing the tiles at one center point corner which you have earlier marked. Then you should proceed until you will be reaching the walls at the side of the room.
If by the time you reach the edges the distance does not correspond to the actual fitting, cutting the slab would be necessary, however, you have to get the accurate distance yet. Usually, a wet saw will be utilized in doing this and this can be bought from any supply centers. The outcome will still have to be sanded with the appropriate coarse prescribed.
Furthermore, you will then be ready to place the slab permanently based on the dry run you previously conducted. You also need to put the mortar set according to the thinness that is prescribed on the borders. After placing the first, you now have a reference point for all the others that will be laid out thereafter.
Finally, what you will be applying last in the installation of marble tile Los Gatos is the grout which must be placed on those lines between the tiles with the use of rubber float. This is preferred by a lot of contractors because it make the work more efficient as it can be forcing through the gaps. Then, remove the excess of the mixture from the surfaces.
The first matter that that you should be concerned of is to ensure if the flooring is stable by doing a test and in doing so, have it be bare to know its sturdiness. Identifying how sturdy it is is through checking of it will shift or if there are presence of cracks. Also, the bouncing test can be done by requesting another to jump at one place and inspecting the vibration in another spot.
The next matter that need your consideration is how you will level the floor and numerous manufacturer nowadays would certainly give the recommendation that you should follow the standard measure of the slope. You will be obtaining a lot of figures but the highest will be the base. The gaps of the levels should also be taken care of and to solve this, you can use a leveling compound.
Another matter that should not be forgotten is the undercutting of the jambs and to start with this step you have to obtain first a plywood. This will used in determining the thickness of the slabs as well as how thin should the mortar be applied. Then, if you have already determined these, you will now have an idea how the door jambs will be accommodated.
One more matter you should also be taking note of in doing the project is the point of the center which should be marked as that will be necessary for the steps that will be following. You will be able to determine this by by securing the meters of the width and the length of the room. Then, you will have an idea on the whole area to be covered.
Moreover, temporary laying out would be helpful like conducting dry runs since this will be your basis as you plan the set up of the installation. You should start with placing the tiles at one center point corner which you have earlier marked. Then you should proceed until you will be reaching the walls at the side of the room.
If by the time you reach the edges the distance does not correspond to the actual fitting, cutting the slab would be necessary, however, you have to get the accurate distance yet. Usually, a wet saw will be utilized in doing this and this can be bought from any supply centers. The outcome will still have to be sanded with the appropriate coarse prescribed.
Furthermore, you will then be ready to place the slab permanently based on the dry run you previously conducted. You also need to put the mortar set according to the thinness that is prescribed on the borders. After placing the first, you now have a reference point for all the others that will be laid out thereafter.
Finally, what you will be applying last in the installation of marble tile Los Gatos is the grout which must be placed on those lines between the tiles with the use of rubber float. This is preferred by a lot of contractors because it make the work more efficient as it can be forcing through the gaps. Then, remove the excess of the mixture from the surfaces.
About the Author:
When searching for quality marble tile Los Gatos homeowners should refer to our official website on www.crafttileinc.com today. See our extensive online catalog at http://www.crafttileinc.com now.
No comments:
Post a Comment